All calculators
(EN ISO 13786)Guide · Summer comfort

Cool homes in summer:the thermal time lag.

In winter what matters is how much heat leaves the house; in summer, when and how much heat gets in. The time lag measures exactly that: how many hours the afternoon heat takes to cross walls and roof. Here you find what it means, how to read it and the values of the most common timber build-ups.

Pencil sketch: the heat of the afternoon sun slowly crosses the wood-fibre wall and reaches the bedroom at night, attenuated

Three numbers to understand summer comfort

01

Time lag

The delay, in hours, between the temperature peak outside and the peak reaching the inside surface. If the sun heats the wall at 3 pm and the time lag is 12 hours, the heat gets inside around 3 am, when it is already cool outside and opening the windows is enough.

02

Decrement factor

How much the heat wave shrinks while crossing the build-up. A factor of 0.10 means only 10% of the outside swing reaches the inside: an 11 °C swing outside becomes about 1 °C inside.

03

Periodic transmittance YIE

It combines both effects in a single value (W/m²K) and is the one required by Italian law: below 0.10 for walls (or mass over 230 kg/m²), below 0.18 for roofs. The lower it is, the cooler the house stays.

Watch a summer day inside the house

The example uses an X-LAM wall with wood-fibre external insulation. The afternoon heat takes many hours to cross the wall and reaches the inside at night, much weaker: that is the moment to open the low and high windows, so cool air comes in and warm air leaves from the top (stack effect).

OUTSIDE in the sun40,0°CINSIDE the house25,7°C15:00

Afternoon: the sun heats the wall the most, peak at 15:00. Inside, the house stays cool.

Illustrative animation: outside sol-air wave peaking at 40 °C at 15:00, time lag and decrement of your build-up, night ventilation from 21:00 to 7:00 when it is cooler outside than inside.

Summer performance classes

The Italian national guidelines for energy certification classify the envelope by time lag and decrement factor.

ClassTime lagDecrementPerformance
Iover 12 hbelow 0.15Excellent
II10 – 12 h0.15 – 0.30Good
III8 – 10 h0.30 – 0.40Average
IV6 – 8 h0.40 – 0.60Sufficient
Vbelow 6 hover 0.60Poor

Time lag of timber walls and roofs

Values calculated live with our calculator for the ready-made models (zone E, inside 20 °C). Change materials and thicknesses in the calculator below to get the values of your project.

Build-upThicknessU W/m²KTime lagDecrementClass
Timber-frame wall with wood-fibre ETICS256 mm0,20010,6 h0,37III
Ventilated timber-frame wall with timber cladding278 mm0,15910,5 h0,32III
X-LAM wall with graphite EPS ETICS259 mm0,1817,6 h0,37IV
X-LAM wall with wood-fibre ETICS331 mm0,16416,3 h0,07I
Ventilated rafter roof with wood fibre280 mm0,16010,9 h0,31III
Ventilated X-LAM roof with rock wool340 mm0,14114,7 h0,15II
Ventilated X-LAM roof with PIR260 mm0,1349,3 h0,30III

What keeps a timber house cool

  1. 01

    Insulation with high heat capacity

    Wood fibre stores about 2,100 J/kgK against 1,000–1,450 for mineral wools and polystyrenes: with the same thickness and a higher density it slows the heat wave much more.

  2. 02

    Mass where it is needed

    An X-LAM panel combined with wood-fibre external insulation adds mass and heat capacity: it is the combination that most easily takes the time lag beyond 12 hours.

  3. 03

    Ventilated roof and façade

    The ventilated gap under the tiles or behind the timber cladding removes much of the sun's heat before it reaches the insulation.

  4. 04

    Light colours and shading

    A light roof covering and sunshades or shutters reduce the temperature the sun brings to the surfaces: the wave to be delayed starts lower.

  5. 05

    Night ventilation

    The time lag works if the heat is let out at night: open windows or mechanical ventilation in the cool hours complete the work of the envelope.

Calculate the time lag and U-value of your build-up

Pick a timber-frame or X-LAM wall or roof, change materials and thicknesses: you instantly see time lag, decrement, U-value, legal check and condensation risk. You can compare up to three build-ups and download the PDF.

Enter your email to use the calculators

We ask only once: afterwards you can freely use all the calculators on the website.

We use your email to manage your access to the calculators. Advertising consent is optional and can be withdrawn at any time. Privacy policy

Indicative estimate, it does not replace the calculation of a qualified engineer. Transmittance to EN ISO 6946 (Rsi 0.13 walls / 0.10 roofs, Rse 0.04; layers with studs: mean of upper and lower limits; beyond a strongly ventilated air gap Rse = Rsi). Time lag, decrement and YIE to EN ISO 13786 over a 24-hour period. Condensation: steady-state Glaser method in the design conditions entered (EN ISO 13788), without monthly balance. U limits: Italian DM 26/06/2015, values from 2021. Material properties: typical values, to be replaced with those declared by the manufacturer.

FAQ

Frequently asked questions about the time lag

At least 10 hours, better over 12: the afternoon peak then reaches the inside at night, when it can be removed by opening the windows. The decrement factor matters too and should stay below 0.30.

It depends on the build-up, not on the structural material. With high heat-capacity insulation such as wood fibre and a ventilated roof, timber walls and roofs reach time lags of 12–16 hours, in line with or above many masonry walls.

With the same thickness wood fibre, thanks to its higher density and specific heat, gives longer time lags. High-density rock wool is a good compromise when non-combustible fire behaviour is also needed.

DM 26/06/2015 requires, in locations with strong solar radiation and outside zone F, walls with surface mass over 230 kg/m² or YIE below 0.10 W/m²K, and roofs with YIE below 0.18 W/m²K.

No: it is an indicative estimate with typical material values, useful for comparing solutions. The final calculation must be done by a qualified engineer with the manufacturers' declared data.

Why trust us

Figures, certifications and public works that speak for us.

1905
Year founded
944
Structures built
9.000 m³
Timber processed every year
  • CE0407-CPR-1459
  • ISO 9001n. 3919760
  • PEFCCSQA-PEFC-COC-54966
  • STCAttestato 22/22-CL
Attachments (optional)

By submitting you consent to the processing of your data to handle your request.